Anycubic
0102030405
ANYCUBIC Wash & Cure Max Detergent Saving 50% , Dual-Cleaning Mode with 14.9L Ultra-Large Wash and Cure Station
VIDEo
DESCRIPTION
【Detergent-Efficient】, Wash & Cure Max's full cleaning process requires only 4L of detergent to be prepared and can be recycled with no direct contact throughout, saving more than 50% on detergent compared to traditional wash and cure station. One bucket of detergent supports the cleaning of 20 models of 10.1" height, and the loss of alcohol in a single cleaning process is less than 50ml.
【One-click Washing and Curing】,The cleaning and curing process is scientifically set up at the factory, just click the auto button and start it, the wash & cure max will automatically cure the 3d models after cleaning them. Experience streamlined model processing that saves you time and effort.
【360° Dimensional Curing】, Featuring a 360° automatic rotating curing platform, this machine provides higher curing energy values and longer irradiation distances, enabling comprehensive, efficient curing for your models.
description2
characteristic
- ControlPanel: Setthe working mode and timeDoor: To block the detergentspray and UVlightTray: Load the printed objects during washing and curingStrainer: To filter the residueUVLight: To cure the printed objectsSprinkler: To spray the detergent/waterWater Container: To load the waterWaterInlet: To connectthe pipe 2Detergent Container:To load detergent
- DetergentInlet: To connectthe pipe 1Detergent Outlet: To connectthe pipe 3Bucket: To collectthe wasteWaste Output: To connect the pipe 4Rated Power: 144WInput Voltage: AC110-240V 50/60HzUV wavelength: 405nmProduct DimensionWashing/ Curing Volume: 434mm(L)*434mm(W)*556mm(H)300mm(L)*165mm(W)*300 mm(H)Weight: 13.5kg
description2
Advantage
Auto Mode
This one-key operation can help you to finish both washing and curing, The working time of this mode cannot be modified
Cure Mode
This operation only cure the printed objects.
* Can be used with just about any resin printer. It works just as well with my QIDI Shadow as it does for AnyCubic's resin printers. If you have a super large print (like something that could be printed on the S-Box or the Saturn) you would likely have a problem with the size, but most prints will fit in this machine.
* Comes with extras that allow you to wash on or off the build plate.
* Seriously easy to use.
* Timer options. 2, 4, and 6 minutes. For both washing and/or curing.
* Stop button so you can stop mid-wash or mid-cure if needed
* Excellent washing. I mean it, this sucker creates a tornado. It gets in those hard to reach spaces. And it changes spin direction halfway through the wash.
* Safety - it only works when the lid is on. So you don't have to worry about being blinded by UV light if you accidentally start it without the lid on (ask me how I know)
* Can handle any liquid. I've used IPA, Mean Green, Simple Green, and Denatured Alcohol. It works great with all of them. (Denatured Alcohol works the best for me.)
* Looks and feels great. It has a minimal foot print and can easily be placed next to the resin printer on an IKEA Lack table (you FDMers out there know what I mean, right?) It's also solid. It doesn't feel like cheap plastic. Not even the lid.
* They have their own Facebook Group with active AnyCubic employees
description2
details
description2
About this item
wash cure max reviews
This is a great addition to your resin printer. The ability to cure the models evenly while protecting you from the UV light is wonderful.
The wash feature is amazing. The lid locks down with a seal so you can leave the alcohol in the container without fumes or fear of a fire. It gets my models clean even with 70% isopropyl vs the 90% so it saves me money.
I bought my printer (Anycubic Photon) and have been printing for a few months now. When researching what I needed for cleaning and post-processing before my purchase, I found number of DIY solutions for washing away resin and curing the final print. Although they worked, they typically took up too much space (one setup for cleaning, another for curing), did a sub-par job, or both.
Enter the Wash and Cure Station. It is extremely effective at washing even the deepest books and crannies, and has plenty of room for the Photon's buildplate. The basket is also a handy option for when you have a rather crowded build plate--just pop em off and into the basket to ensure proper flow around the part for cleaning. The cure function works great, and the timed stop allows me to walk away and work on other things.
However, the biggest benefit is the machines size. At roughly the same size as the Photon, it does the job of two pieces of DIY setups that are often large and/or clunky. As space is at a premium in my workspace, this was the kicker for me. My work flow has been extremely easy (printer to wash/cure machine) and has cut down not only on the post-processing time, but also cuts down on the number of paper towels needed for each printing run as you don't have to move the print as much.
When I bought the machine, my primary concern was the price. However, after having used it, I can say it was well worth the money. It isn't necessary by any means, but it did ease the transition from FDM printing into the world of DLP.
Makes the cleaning and curing process 90% faster and less messy. Found the USB light to be hard to get in but once it clicked it was snug.
FAQ
1.The machine does not work.
Poor powercontact.Pulloutthe power cord and plugitin again.
Please contact ourtechnicalsupport ifthe solution above cannot solve your problem.
2,The rotor inside the washing drum does not rotate during the washing process. The rotorinside the washing drum is stuck byforeign matter. Press RESET button and wait for the machinestops, Then, turn off the machine and open the door to remove the foreign matter.Then turn on the machine to wash and cure.
There are too much precipitation in the solvent.Press RESET button and wait for the machine stops.
Then,turn off the machine and open the door to cleaning the precipitation.
Then turnon the machine to wash and cure.
3.The machine has abnormalsound duringoperation.
The ground where the machineis placedis not flatenough.
.Thescrewon therotorisloose.Tighten the screw.
4.Partofprintobjects are white after wash and cureThe concentration ofthe alcohol which is used for washing is not high enough.Use alcoholwith concentration exceeding95%.
5. When mode button is pressed to switch mode, the two mode lights are not lit.Try again orrebootthe machine.
6.The machine does not work and reports error:E20The dooris not closed.Close the doorandthe machine will work
7.The machine pauses the washing andreports error:E11 Thereis no water. Check the water volume and fill up the container. Then, press START/STOP button and themachine willcontinuethe processbefore.
8.The machinepauses the washing andreports error:E12
The outlet of water/detergentis blocked.The door willunlock this time.Please clean the blockage in the drum or drainer, Then, close the door and press START/STOP buttonThemachine willcontinuetheprocess before.
The machine is notlevel. Please place it to a stable,levelworkspace. Then, close the door andpress START/STOP button. The machine will continue the process before.